3d Printer Fan Duct Design
Remixed Fan Duct Design-Flashforge Creator Pro
thingiverse
This is a cooling fan duct design for a turbo fan. This is much better than the Flashforge duct as this one cools both hotends. Print Settings Printer: Flashfore ...
cr10s Pro Fan Duct (Fixed Design)
thingiverse
Fixed the design to properly fit my cr10s Pro. ...the original design didn't fit properly and left an 1/8 inch gap causing a loss of airflow. the original file also kept rubbing against the fan. ...I fixed all of the issues with this remix
Modified Wanhao i3 fan duct designed by Thorped
thingiverse
Remixed this for a smoother air flow path.
BFB 3D Touch & 3000 Snap-on Fan Ducts - Simple Design
thingiverse
... A small tab on the duct rides against the bottom of the fan body to hold the bumps in the fan hole 'detents'. ... I have no idea yet what effect these ducts will have on printing, but the theoretical increase in part cooling should reduce warping.
DAN A4 92mm Fan Duct in ASUS ROG Design
thingiverse
This Fan Duct is designed for a 92mm Fan. ...Because of the height, it is fitting perfectly in the DAN A4 Case using a Noctua NH-L9i Cooler.
Fractal Design Node 202 GPU Fan Duct
thingiverse
-Modified the position of the ducts slightly (1 mm) to better match my GPU (also an EVGA, so I suspect they use the same design) -Modified the duct geometry to have a more consistent wall thickness. This was difficult to do with the full size case...
Modified High Speed Ducted Fan. 2mm Shaft. Designed for RF-310T-11400 or DLK120514. (Untested).
thingiverse
This is a modified version of Mirkoengineer's High Speed ducted fan with a 2mm shaft and (I think) faster print time.
M5 base for TK_DESIGN 40mm Fan Duct
thingiverse
Super minor tweak to enlarge the mounting holes for m5x8 hardware.
Anet A8 Fan Duct
thingiverse
This is my Anet A8 fan duct design. ...please enjoy!
92mm Angled fan duct
thingiverse
92mm angled fan duct. ... Designed for Dan A4 case bottom fan which is normally pointed at the power supply/
Fan duct prusa i3
thingiverse
A simple fan duct design for my extruder, on prusa i3 rework. Work with a 40/40 fan. ...Post-Printing extrud before and after fan duct
i3 mega fan duct + adaptateur
thingiverse
Fan duct design: https://www.thingiverse.com/thing:3537449 I make adaptateur for fix it on stock platine.
60mm to 40mm fan duct Corner aligned
thingiverse
a basic 60mm to 40mm fan duct designed in fusion 360 with loft
FLSUN QQ-S Original Fan Duct
thingiverse
Here is the original fan duct design for the FLSUN QQ-S printer.
Ender 2 Fan Duct
thingiverse
This is the fan duct designed by aemux but adapted for shorter screws. ... I have noticed that printing it rotated -90ยบ on the Y axis strengthens the area that the screws go through.
E3D part cooling fan duct
thingiverse
E3D fan duct design that uses 2 50mmx15mm blower fans. ...This should fit on any E3D heat sink if you have the available clearance for the blowers.
E3D-v6 Fan Duct
thingiverse
It is designed for Injection Moulding, however we want to share it here for anyone wanting to use the STL to incorporate the duct into their design. The design includes the required draft angles for IM components. If there is demand for a version...
30mm Fan duct
thingiverse
This fan duct was designed for hotend's heat sink with 25mm(24.6mm) diameter of the heat sink. ... Instructions I printed the fan duct in silver ABS 0.2 layer height 50% infill 235c no support needed
CR10S Pro/MAX V6 Fan duct
thingiverse
A fan duct designed to fit V6 hotend. No need for extra parts. ...My other desing contain a V6 mount for CR10S Pro/MAX
Artillery Sidewinder X1 / Artillery Genius Stock-like fan duct for BLTouch mount
thingiverse
New fan duct design. ...This is my favourite design, simple but effective.
Rapide Extruder Fan Duct
thingiverse
This is a replacement rear extruder fan duct design for the Rapide series of printers. I could not find the original file so I recreated the design instead. Print Settings Printer Brand: RepRap ...
ADIMLab Semi-Circular Part Cooling Fan Duct
thingiverse
... used on the ADIMLab printer. ... Uses a 5015 24v DC Fan The regular fan duct design is for the stock hot-end and others of a similar size. ... The volcano fan duct design is for hot-ends that hang lower then stock (such as E3D's Volcano hot-end setup)
Circular fan duct
thingiverse
As my hotend is not centered in the carriage (I'm using Greg's accessible extruder: http://www.thingiverse.com/thing:8252), I have adjusted this fan duct design to short it in 4mm (use on the left side of the carriage). I have also added a clearance...
Bootstrap Anet A8 Fan Duct
thingiverse
A modification of the original fan duct design to print such that there are no bridges or overhangs. Tape the two halves together with duct tape and you have a passable fan duct. ... To use the scad file you'll need to download the stl file for the...
Anet A6 Fan Duct
thingiverse
A couple mm longer duct with rounded inlet. ... NOTICE! This fan duct was designed for this https://www.thingiverse.com/thing:2424312 Probe And Fan Mount and the nozzle may not be centered on y axis with this fan duct on stock A6 mount
Hotend fan duct
thingiverse
Inspired by b2x fan duct, I designed a much simpler one, with a very simple OpenSCAD file you can easily modify. Instructions Print the uploaded STL file. ...Use OpenSCAD file if you want to make any...
60mm fan duct for Ultimaker
thingiverse
This is a derivative of the fan duct design by daid which allows the use of 60mm fans. Instructions Attach a 60mm fan to the ultimaker hotend, this size is easier to find than the standard size. ...I use a noiseblocker 60mm case fan.
Fan duct Anet A6
thingiverse
Warning, this fan duct is designed for a print head that has a "auto leveling bed!" The axis of the nozzle and that the fan is shifted according to the fan 5015 which is also shifted. ...Print Settings Printer Brand: RepRap ...
E3D 30mm fan duct
youmagine
This fan duct was designed to replace the duct that shipped with the e3d v5. It is slightly shortened so that it can be mounted to point away from the x-carriage of the Makerfarm i3v. ...This orientation prevents air from blowing onto the print when...
Part Cooling Fan Duct 15 x 20
thingiverse
Fan duct designed to attach to a 15x20 blower fan for part cooling. I was just playing around with OpenSCAD trying to figure out how to design this... ...and well, it works really well too.
3d Printer Fan Duct Design
Source: https://www.stlfinder.com/3dmodels/fan-duct-design/
Posted by: lincolnancestrand.blogspot.com
0 Response to "3d Printer Fan Duct Design"
Post a Comment